Open topic with navigation

Work Orders

This chapter contains the following topics:

Introduction to Work Orders

Entering Work Orders

Work Order Edit Lists

Committing Inventory

Printing Work Orders

Issuing Work Orders

Printing Issued Work Orders

Quick Work Orders

Introduction to Work Orders

This chapter describes how to do the following:

If you chose not use Kits in Control information, you may skip this chapter.

A work order is a request to assemble a specified quantity of a kit from its component items. Work order is abbreviated as W/O on various screens and reports in Inventory Control. The Kits chapter describes kits and the relationship between a kit and its components.

Work Order Types

A work order can be immediate, in which case the kit is immediately placed in inventory. Alternatively, a work order may be printed, issued, and the component items removed from inventory, but the kit is not placed in inventory until the work order is completed.

When a work order is defined as immediate completion, Inventory transactions are created to remove the components from, and to add the kit to, inventory. The kit is immediately available for sale. No document is printed, and the process of closing the work order does not arise. For an immediate work order, you still have to commit the inventory and issue the work order.

When a work order is not immediate (typically because some time and labor is required to physically assemble the kit), several further steps are necessary before the kit is available for sale. These steps, described in detail in succeeding chapters, are summarized below.

Work orders are entered and completed individually. The other functions (committing, printing, issuance, and closing) operate upon the work orders as a group (optionally restricted by range or other properties) much as posting does in other selections.

Entering Work Orders

Select

Enter from the Work orders menu.

The following screen displays:

Enter the following information:

1. Work order #

If you want a new work order, use the <F2> key to generates a new work order number by adding one to the previous number used. The initial value is set in Control information.

Enter an existing work order number.

Options 

You may also use one of the options:

Entering a number that is already on entered, or using the <F1> or <SF1> keys, loads the screen with the data for that existing work order and positions the cursor at the Field number to change ? prompt. You may then change or delete the work order.

2. Kit item #

Kit items must be defined via the Items selection, and must already have been defined as a kit, via the Kits selection. Enter a kit item number.

Options 

You may also use one of the options:

3. Work order date

Enter the date to be assigned to this work order press <Enter> for the default date. For the first W/O entered, the default is the System date; thereafter, the date of each work order entered becomes the default for the next

4. Kit quantity required

Kit quantity required is almost always an integer, but fractional quantities are permitted if the kit is not serialized. This is occasionally useful when dealing with kits assembled from components that can be measured but not counted. For example, 105-octane gasoline might be defined as a kit assembled from an 80-octane component and a 120-octane component in a certain proportion. You might then have as a result 250.35 gallons of the 105-octane gasoline and would enter that as the kit quantity.

Enter the number of kits to be assembled for this work order.

5. Work order reference

Enter a reference for this work order. This field is optional and is provided so that you may enter a customer number, purchase order number, or whatever reference you choose.

Later, you will be able to locate an incomplete work order using this reference. This is useful if you need to determine if a work order for a specific customer has been completed or not. Using View work order history, you will also be able to locate a completed work order using this reference.

6. Immediate completion ?

An immediate completion work order renders the kit-item available for sale now. Typically you would use this feature for kits needing little labor or time for assembly.

If you answer N the work order is processed as a normal work order. You must commit, issue, complete, and close it before you can sell the kit or before inventory is adjusted.

If you answer Y, then:

Unlike regular work orders, immediate work orders can not be committed if there is a shortage of needed components. Attempting to do this generates the message Inventory short.

Received further inventory, or Identified and deleted the work order(s) whose components you have pre-empted.

7. Targeted completion date

This field does not apply to immediate completion work orders.

Enter the target date on which this work order is to be completed. This date will appear on screens and reports used to track incomplete work orders.

8. Print work order?

This field does not apply to immediate completion work orders.

If the nature of your business is such that you do not require a printed document, answer N. The work order will still have to be issued even though not printed. If you change your mind later you may obtain a copy via the Print issued work orders selection, if the work order has already been issued; or via the Print work orders selection, if it hasn't. Once the work order is completed it may no longer be printed.

9. Work in Process account

This field does not apply to immediate completion W/O’s.

When the component usage transactions for the work order are posted, the work in process account entered here is debited for the cost of each component item. These items are retained in the work in process inventory until the corresponding kit assembly transaction is posted after closing the work order (using Close work orders).

Enter an existing work in process account or press <F2> for work in process account.

10. Commit component quantities when partially available?

Prior to printing this work order, you must commit the inventory quantities for the component items using Commit inventory. When Commit inventory is run, the quantity available for one or more of the component items that you designated as Full amount items in the kit definition (using Kits) may be less than the amount required to assemble the quantity of kits needed.

If you answer Y, then component-item quantities will be committed for all items, even if there is a shortage for the Full amount component items. In this case, the Work Order Status Report will show the amounts committed and the amounts still needed in order to print and issue the work order. Use this report (described in the Committing Work Orders chapter) to determine what receivings are needed to obtain sufficient quantities available to issue the work order. Once these receivings have been entered using Inventory, you may run Commit inventory again to commit the remainder needed to assemble the kit. Then, the work order may be printed and issued.

If you answer N, a shortage of any Full amount item will prevent commitment of all components on the work order. The Work Order Status Report will show the shortages for each component item.

Work orders compete with one another for scarce parts. If you want to ensure that kits are assembled first-come first-served, always respond Y. Understand that this could result in some work orders being delayed even though parts are on hand, because the parts they need are committed to other work orders waiting for other parts.

If you want to maximize turnover and ensure that each part is used as soon as there is a kit ready to use it, always respond N. The danger here is that work orders containing numerous parts could be kept waiting indefinitely because there is never enough at any one time of every part needed. This policy, therefore, requires more careful monitoring than the other.

The next two fields appear only if you use multi-warehousing.

11. Stocking warehouse

This is the warehouse where the assembled kit is to be stocked. The kit item must already be defined (in Items) as stocked at that warehouse.

Enter a warehouse code.

Options 

You may also use one of the options:

The description of the warehouse appears next to its code as soon as one has been selected.

12. Override Kit component Warehouses ?

Answer Y if you wish to override.

Make any desired changes.

Options 

You may also use one of the options and press <Enter>.

Deleting Work Orders

When a work order is deleted after inventory has been committed to that kit, any serialized components are released. They become available for sale or for incorporation into another kit.

To enter or view existing comments about this work order, press <F6>.

Entering Comments

Press <F6> to enter up to 10 lines of 64 characters each.

Options 

When you press <Esc> from the comments window, you have these options:

Work Order Edit Lists

This selection enables you to edit and display all or a range of work orders.

Select

Edit list from the Work orders menu or Work order edit list from the Reports, kits menu.

The following screen displays:

Enter the following information:

1. Starting work order # and
2. Ending work order #

Enter the range of work orders to appear on the edit list or press <F2> for First and Last at each field.

3. Cut-off targeted completion date

Enter the last targeted completion date for which work orders are to be included on the edit list or use the options below. Work orders with a targeted completion date later than this date will not be included.

Press <F2> for Latest (no cutoff date)

4. Work order status

The status of a work order changes as it proceeds through the various steps of processing. These are listed in the table below.

Enter one of the statuses listed.

Options 

You may also use the options:

Note that Issued is not listed as a status. A separate selection is available to print issued work orders. Refer to the Print Issued Work Orders chapter.

Committing Inventory

Prior to printing a work order, you must commit the inventory quantities for the component items using Commit inventory.

When Commit inventory is run, there may be insufficient quantities available for one or more component items that you designated Full amount in the Kits selection.

If you answered Y to Commit inventory when partially available? on the work order, then component-item quantities will be committed for all items. In this case, the Work Order Status Report will show the amounts committed and the amounts still needed in order to print and issue the work order. Use this report to determine what receivings must be done in order to have sufficient quantities available to issue the work order.

For shortages on Full amount component items, once receivings have been entered using Inventory, you may run Commit inventory again to commit the remainder needed to assemble the kit. Then, the work order may be printed and issued.

If you answered N to Commit inventory when partially available?, then no component items are committed if there is a shortage of any Full amount items. The Work Order Status Report will show the shortages for each component item.

The Work Order Status Report is printed as part of running Commit inventory. It shows the status (as described earlier) of each work order processed. For work orders with insufficient quantities available for Full amount components, or with insufficient quantities for Shortage OK components, actual shortages are shown on the report. Shortages of Shortage OK components do not prevent a work order from being printed and issued. They are listed on the Work Order Status Report for your information.

Select

Commit inventory from the Work orders menu.

The following screen displays:

Enter the information as follows:

1. Starting work order # and

2. Ending work order #

Enter the range of work order numbers for which to commit inventory or press <F2> for First and Last at each field

3. Cut-off targeted completion date

Enter the last targeted completion date for which to commit inventory for work orders. Those with a targeted completion date that is later than this date will not be processed by Commit inventory. Press <F2> for Latest (no cutoff date).

Printing Work Orders

This selection enables you to print all or a range of work orders. If you specify that a work order must be printed prior to being issued, then print it using this selection.

Immediate completion work orders cannot be printed

If you specify that a work order must be printed prior to being issued, then print it using this selection.

Select

Print work orders from the Work orders menu.

The following screen displays:

Enter the information as follows:

1. Starting work order #

2. Ending work order #

Enter the range of work orders to print or press <F2> for First and Last at each field.

3. Cut-off targeted completion date

Enter the last targeted completion date for which to print work orders. Work orders with a targeted completion date later than this date will not be printed. You may also press <F2> for Latest (no cutoff date).

4. Reprint work orders already printed?

Answer Y to reprint work orders that have already been printed.

If you are using multi-warehousing, an additional field appears:

5. Print in order by

Select S by stocking warehouse, or W by work order number.

If you select S to print in order by stocking warehouse, field #6 appears as follows:

6. Stocking warehouse

Enter a warehouse. Work orders are printed if their kit items are to be stocked at this warehouse.

Options 

You may also use one of the options:

Issuing Work Orders

A work order may be issued if it has the status OK to issue. This status is assigned when the following has occurred:

When a work order is issued, component usage transactions are generated in Inventory Transactions for each component-item of the work order. Additionally, the Qty on W/O for each kit-item is increased.

For an immediate completion work order, a kit assembly transaction is generated in addition to the component usage transactions. However, the Qty on W/O is not increased for the kit-item because the work order is considered to be completed immediately. However, the generation of the kit assembly transaction increases the quantity of the kit-item available for sale by decreasing quantity committed for the kit-item.

Select

Issue work orders from the Work orders menu.

The following screen displays:

Enter the following information:

1. Starting work order # and

2. Ending work order #

Enter the range of work orders to issue or press <F2> for First and Last at each field.

3. Issuing date

Enter the issue date to be assigned to these work orders. This date is used as the date for the component usage and kit assembly transactions that are placed in Inventory Transactions. You may also press <Enter> to use the System date.

4. W/O cut-off date

Enter a cut-off date for the work orders to be issued. Work orders with a Work order date that is later than this date will not be issued. You may also press <Enter> to use the date entered for Issuing date.

5. Print W/O register?

Answer Y to print a Work Order Register.

If you chose to print a Work Order Register, then select to print the register in either F (full) or B (brief) format.

If you are using multi-warehousing, an additional field appears:

If you chose to print a Work Order Register, a new section of this field will appears, then select to print the register in either F (Full) or B (Brief) format.

Options 

You can use one of the following options :

6. Issue in order by

Enter S to issue work orders by stocking warehouse, or W by Work order number.

Options 

You may also use one of the options:

If you enter S for Issue in order by, field #7 appears as follows:

7. Stocking warehouse

Enter the stocking warehouse for which to issue work orders.

Options 

You may use one of the options:

Make any desired changes, or use one of the options, and then press <Enter>.

Printing Issued Work Orders

Use the Print issued work orders selection to print additional copies of non-immediate work orders that have been issued.

You may also use this selection to print don't print work orders (i.e., work order was originally specified to not print).

Work orders may not be printed using this selection after they are closed using Close work orders, or if they were specified as immediate completion when the work orders were entered.

Select

Print Issued work orders from the Work orders menu.

The following screen displays:

Enter the information as follows:

1. Starting work order # and

2. Ending work order #

Enter the range of work orders to print or press <F2> for First and Last at each field

3. Cut-off targeted completion date

Enter the last targeted completion date for which to print work orders. Work orders with a targeted completion date later than this date will not be printed. You may also use press <F2> for Latest (no cut-off date)

4. Include "Don't print" work orders ?

Do not print work orders are those for which you answered N to field # 8 (Print work order ?) in Work orders (Enter).

If you answer Y, all work orders will be printed. If you answer N, Do not print work orders will not be printed.

Immediate completion work orders are never printed.

5. Print in order by

Enter S by stocking warehouse, or W by work order number.

Options 

Use one of the following options :

If you enter S for Print in order by, field # 6 appears as follows:

6. Stocking warehouse

Enter a warehouse. Work orders will be printed if their kit-items are to be stocked at this warehouse.

Enter the stocking warehouse for which to issue work orders.

Options 

You may also use on of the options:

Make any desired changes, or use one of the options, and then press <Enter>.

Quick Work Orders

Use the Quick work orders selection to process a single step work order.

Select

Quick work orders from the Work orders menu.

The following screen displays:

Enter the information as follows:

1. W/O- #

Enter the number of the quick work orders to process.

Options 

You may also use on of the following options:

2. Date

Enter the date for this quick work order or press <Enter> for the System date.

3. Kit ItemAn item is a clearly identifiable product, material, or commodity that can be stocked, sold, or used. Inventory Control maintains a file of inventory items. Each item is identified by a unique number and a description. Other information maintained for an item includes cost, price, product category, quantity on hand and reorder level.-#

Enter in the kit item number you are building.

Options 

You may also use one of the options:

4. Disassembly ?

Enter Y to disassemble and N to not disassemble.

5. Quantity

Enter the quantity of kits you will be building. If disassembly enter the quantity of kits you are removing.

6. Employee #

Enter your employee # or any numbers. You cannot leave it blank.

This field does not print on any reports or view screens. It is only available through SQL tables or XDBC. It is stored in Quick Work Orders (QIKWRK) and Work Order History (WKOHDR). It is the employee number (emp_no) column in both cases. See the Field Definition Guide for details on the tables and columns.

7. Kit warehouse

This field can only be entered if you are using multiple warehouses.

Enter a warehouse or press <Enter> for the Central warehouse

Make any changes or press <Enter> at Field number to change ?. The following screen displays:

This screen allows you to modify the components items, quantity and warehouse if they differ from the original entry under Kits.

You may use the following options:

When inserting or entering a new component, you must enter the following fields:

Item-#

Enter the component item number.

The item must already have been defined as an item in the Items selection.

Need

Enter the number of component-items required to assemble one kit item. Press <Enter> to default to a quantity of 1.

Whs

This field may not be entered if you are not using multiple warehouses.

Enter a warehouse code, or use the option:

Serial-#/Lot-#

If you have serialized or Lot controlled items, you must enter serial and lot numbers for this item.

Press <Esc> when you have made your changes and entries and the following options display:

Options 

The options that become available are:

Open topic with navigation